VETO PROPAC USA TECH-PAC BLACKOUT AX3561

Tech Pac Blackout Backpack COMES WITH VETO Pro Pac’s V-Swap™ REMOVABLE AND EXCHANGEABLE Tool and Meter Panels; V-Swap™ Laptop, Bulk Storage, Modular, Utility and Folio Panels SOLD SEPARATELY. Additional tool and meter panels may also be purchased separately

The Tech Pac Blackout is a blacked-out tool backpack for tool storage based on our Tech Pac but with Veto Pro Pac’s V-Swap™ system that COMES WITH FRONT AND BACK removable TOOL and METER pocket panels which are also exchangeable. You can also purchase a Laptop Panel that can turn the bag into a tool bag/laptop bag, and the Laptop Panel can go in the front or the back, and a flat rubber panel for Bulk Storage. Includes V-Swap™ Tool Panel and Meter Panels, V-Swap™ Laptop, Folio, Utility, Modular, and Bulk Storage Panels Sold Separately.

PRODUCT SPECIFICATIONS:

• Height (H): 19.5” (49.5cm)
• Width (W): 13" (33cm)
• Depth (D): 10" (25cm)
• Handle Height (HH): 22" (56cm)
• Weight (empty): 10 lbs (4.5kg)
• Internal Volume: 1550in³ (25L)
• Max Payload: 50lbs (23kg)

MAXIMIZED TOOL STORAGE CAPACITY:

• Vertical Tool Pockets: 46 interior and exterior tool pockets of various sizes
• Upper Pockets (Front Side) Designed For Extra Tool Capacity
• Swap-Out Tool Panels- Front and Back Tool Panels are removable and exchangeable
• Laptop Panel Available as an accessory (must be purchased separately).
• 8" Electrical Tape Strap
• 2 Storage Bays- 4 Storage Platforms
• Manifold Gauge and Hose Storage Pocket
• D-Rings: 4 large and 5 small
• Outside Mounted Stainless Steel Tape Clip Holder

RUGGED MATERIALS & CONSTRUCTION:

• LOAD TESTED: PULLED TO DESTRUCTION AT 830 POUNDS (Handle failed); Hook failed at 200 Pounds
• Weatherproof Base: 3mm Injection Molded Polypropylene
• Tactical All Black Polyester Body Fabric (phthalate free) & Interior Construction - Gray Pockets For Better Visibility
• Quick Release Metal Hasp: Allows Easy Access to Rear Storage Bay
• Internally Stored Aluminum Hook to Hang Bag
• Over-Molded Ergonomic Grip
• Padded EVA Thermoformed, Ergonomic Back Padding
• Metal Shoulder Strap Sliding Buckles
• D-Rings: Powder Coated Steel
• Rivets: Marine Grade Rivets
• Stitching: Industrial Strength Double Nylon Stitching

OTHER FEATURES:

• Includes Front Tool Panel and Back Tool & Meter Panel, Laptop Panel Sold Separately
• Metal YKK® Locking Zippers
• Magnetic Screw Catcher
• Warranty: 5 Years (see Veto warranty terms and conditions)

Additional Information:

Weight: 10 lbs

Dimensions: 13 × 18.75 in

VETO PRO PAC - TOOL BAGS PRODUCT CARE & MAINTENANCE

Keep your zippers clean and properly lubricated

Over time, dirt and grime will clog your zipper coils, preventing them from staying closed. To prevent this from happening, clean and lubricate your zippers twice a year (more often if you work on a dusty construction site).

To clean the coils: Scrub them with soapy water, using a toothbrush. After scrubbing the coils, blow them with air to remove any other fine hairs that were not removed with the brush. To lubricate the coils: Apply a silicone spray, beeswax, or zipper lubricant.

Protect zippers from sharp objects and excessive heat

Any sharp object or heat source can permanently damage zippers. Once a zipper coil is cut or snapped, the zipper will not work and in most cases cannot be repaired.

Most of the cut zipper coils we see are the result of sharp tools being stored inside the bag with the sharp side facing up. Be sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.

Do not overstuff the bag.

Overloading your tool bag will most likely cause significant stress on the zippers, above and beyond what they were designed for and will eventually cause the zipper(s) to separate.

If you have to strain to close your zipper, your tool bag is probably too full... Remove something, rearrange, or proceed with caution, always keeping in mind that you risk violating the terms of your warranty.

Learn more here